How to remove electric baseboard heater

10 Dec How to remove electric baseboard heater

If you need to replace an old electric baseboard heater, there’s no need to pay someone else to do it. If you have basic DIY skills and can follow simple instructions, this project is easy enough for anyone to handle. The most important thing is to always turn off the power before working on any electrical wiring. This content is presented by https://accurehome.com/

How to remove electric baseboard heater?

Here are the steps you need to follow:

Shut off the power to the baseboard heater

Before you begin to remove the baseboard heater, it’s important that you turn off the power to the outlet and heat. If there is a circuit breaker in your box, turn it off. If there is a switch in your box, flip it to “off.”

Disconnect the wires from the unit

Unplug the heater. If you’re not sure how to do this, see our article on how to unplug a space heater.

Remove the wires from the wall. This is probably one of the most important steps in removing an electric baseboard heater, so don’t skip it! You will need to disconnect these wires before taking out any other parts of your baseboard heater. If you are not sure which wire goes where, label them with masking tape before removing them from their sockets and then reconnecting them later without worry of confusion! Let’s discover: How to move out of a toxic home

Remove any screws connecting the heater to the wall

Remove any screws connecting the heater to the wall. This is done by using a screwdriver to unscrew them from their anchors in the wall. Be careful not to damage any of your walls, as electric baseboard heaters tend to be heavy and can cause severe injury if they fall on you. If you find that some or all of the screws are too tight for your hand-tools alone (or if you need to get into a really tight spot), use a power drill. If there are no screws at all, then it’s time for step two.

Carefully pull the heater away from the wall

Carefully pull the heater away from the wall. Use a flathead screwdriver to pry it away from the wall, being careful not to damage it in any way. Once you’ve done this, use a level to make sure that your new baseboard heater is standing straight and upright against the wall before proceeding with securing it into place.

Remove the trim

To remove the trim, you’ll need to pry it away from the wall with a flathead screwdriver. You’ll want to be careful not to damage your wall in the process, so take care when doing this step. If you do happen to damage your walls, like if you accidentally gouge some drywall or something like that, don’t worry: You can repair it with spackle or putty after removing the electric baseboard heater.

Determine where you need to install your new heater

Use a level and pencil to draw lines in between the marks. Take extra care to ensure your lines are straight and even by using a framing square or measuring tape as a guide.

Once you have marked all of your studs, use a stud finder to locate them on each end of each line that was drawn on your wall. The best way is by using an electronic stud finder because they will be able to detect small pieces of wood behind walls without fail! If you don’t have access to one of these handy devices, then make sure that at least two people are working together so one can hold up their end while another person uses whatever method they prefer for finding studs (such as knocking on walls).

You can use a stud finder to locate the studs in your wall. Once you’ve found them, mark each one with a pencil or piece of tape at 18 inches (46 cm) on center. This will ensure that you know where to drill into the wall when installing your new electric baseboard heater.

Install your new heating unit

With your new heating unit, locate the studs in the wall. Use a stud finder to locate and mark each stud with pencil or tape.

Use a level to ensure that your new heat is straight. Place it horizontally on top of the baseboard heater, then adjust any crooked edges until it’s perfectly level from front to back and side to side.

Screws should be long enough to securely hold down both sides of an electric baseboard heater (you’ll need at least one screw for every two feet).

Conclusion

There you have it! That’s how to remove an electric baseboard heater. If you’ve got any questions, don’t hesitate to reach out. We’re always happy to help with your heating needs.